SYCBCWL089F 6Pin high-current lithium battery female connector, launched by SYC, is an ultra-thin and compact power interface specially developed for high-power-density lithium battery packs. This model adopts a high-strength PA66+GF30 engineering plastic housing, combined with a silicone sealing ring and M3 threaded locking structure, achieving IP67 protection rating, capable of resisting rain, dust, and salt spray erosion; the internal 6 conductive terminals use phosphor bronze base material with surface tin plating process (Sn≥3μm), with a rated current of up to 30A per pin, supporting continuous 150A/60V DC full-load operation across the entire row, with contact resistance ≤0.5mΩ and temperature rise <30K. The external dimensions are only 64.4×18.2×15mm, with a thickness reduced by approximately 5mm compared to conventional models, and both sides are equipped with M3 threaded mounting holes, perfectly adapting to the ultra-thin battery compartment space constraints of handheld power tools, portable energy storage power supplies, drone base stations, and light electric vehicles. It has passed CCC mandatory certification and RoHS environmental directive, suitable for all lithium battery application scenarios with extreme requirements for safety, environmental adaptability, and space efficiency.

SYC (Sinyinda) launched SYCDM27P12R1R2 (LCP gold-plated version), a 12-pin high-density lithium battery connector male header (DIP through-hole type) designed for high-power-density 15A-class power/signal hybrid transmission + space-constrained scenarios. This product features an ultra-compact 2.7mm pitch design, with PCB footprint width of only approximately 35mm, saving 46% lateral space compared to traditional 5.0mm solutions. Combined with LCP liquid crystal polymer substrate, the heat deflection temperature is ≥340°C (1.8MPa), capable of withstanding 260°C lead-free wave soldering peak temperature (3-5s) without deformation or blistering, while maintaining stable dielectric constant (Dk≈3.0@1GHz) to ensure high-speed signal transmission integrity. Single-pin rated current is 15A, total current capacity 180A, meeting high-current demands of AI robots, drones, and similar applications. Key upgrade: contact area adopts gold plating process (Au 0.05-0.1μm over Ni), significantly reducing contact resistance to ≤5mΩ, greatly enhancing oxidation resistance and fretting corrosion resistance. DIP through-hole structure with dual alignment posts (height 3.5mm) provides PCB axial retention force ≥100N and radial retention force ≥60N, capable of withstanding repeated mating/unmating and high-frequency vibration stress. Specifically suited for AI robot battery packs, industrial drone power interfaces, portable energy storage BMS, power tool fast-charge modules, and other application scenarios with rigid requirements for "high density + high current capacity + high mechanical strength + 260°C process + signal integrity," precisely pairing with female header SYCDF27P12R1R2 to form a complete 15A-class 2.7mm-pitch high-density DIP lithium battery interconnect solution.

SYC (Sinyinda) launched SYCZF01P5CSMT (PA9T version), a 5-pin lithium battery connector female header (SMT type) designed for 10A-class power and signal hybrid transmission + fully automatic SMT assembly. This product uses PA9T high-performance substrate with heat deflection temperature ≥310°C (1.8MPa), capable of withstanding 260°C lead-free reflow soldering peak temperature (10s) without deformation or blistering; CTI value ≥400V (33% improvement over PA6T's 300V), meeting stringent insulation requirements of IEC 60664-1 overvoltage category III, pollution degree 3. The 5.0mm standard pitch ensures creepage distance ≥4.5mm, single-pin rated current 10A, total current capacity 50A, supporting integrated BMS communication lines and power lines in the same port. SMT structure with dual alignment posts provides PCB retention force ≥80N, with vibration and shock resistance meeting automotive-grade LV214 standard. Asymmetric housing + guide groove provide dual anti-mismating protection, completely eliminating reverse insertion risk; tin-plated contacts (3-5μm) balance solderability and wear resistance, with mating cycle life ≥500 cycles. Specifically suited for automotive BMS sampling ports, energy storage high-voltage box interfaces, industrial AGV charging contacts, medical portable device power modules, and other application scenarios with rigid requirements for "260°C process + high CTI insulation + 10A hybrid transmission + SMT automatic assembly," precisely pairing with male header SYCZM01P5R1H590 to form a complete 10A-class 5.0mm-pitch high-reliability lithium battery interconnect solution.

SYC (Sinyinda) introduces the SYCBCJY16PM 16-position connector male header, a micro precision interface designed for ultra-high-density signal and power hybrid transmission. This product features a high-strength PA engineering plastic housing with copper-gold-plated (1u) contacts, achieving 16 independent channels within a compact footprint of only 42.0mm × 10.5mm; rated current 5A, rated voltage DC 500V, with transient current up to 7A, meeting the demands of multi-channel signal and low-power hybrid transmission. It is RoHS certified, with a recommended mating cycle life of up to 2000 insertions, and features four M2 countersunk screw holes at the corners, making it perfectly suited for scenarios demanding extreme space efficiency and signal integrity, such as drone flight controller expansion modules, multi-channel hubs for RC receivers, multi-parameter monitoring cables for medical equipment, and industrial automation control systems.

SYC (Sinyinda) introduces the SYCBCHF01P4DIP, a 4-pin high-current female connector (solder-tab type) designed for 80A-class pure power lithium battery transmission scenarios. This product features 4 identical 20A power terminals, supporting 4-way parallel current sharing to achieve 80A continuous current carrying, and offers true N+2 redundancy—even if one pin fails, the remaining 3 pins can still carry a 60A normal load without interrupting power supply; with two pins failed, it can still maintain 40A emergency operation. It employs copper-nickel plated (50-80μ") high-wear-resistant contact technology, with a mating cycle life of ≥1000 insertions and stable contact resistance of ≤3mΩ; the PA66 insulating substrate combines mechanical strength with temperature resistance, rated voltage DC 250V, operating temperature -40℃~+105℃. The four-hole positioning design ensures installation accuracy of ±0.1mm, and the asymmetric housing provides physical reverse-polarity protection, with a recommended mating cycle life of 1000 insertions. The U-slot structure supports direct crimping and soldering of AWG 10-18 wires without pre-tinning, significantly improving assembly efficiency. It is particularly suited for applications with rigid requirements for "80A-class power + flexible wiring + manual/semi-automatic assembly," such as TWS earbud charging case super-fast charging ports, smartwatch magnetic charging bases, micro drone battery interfaces, and medical portable device power modules, pairing precisely with the male connector SYCBCHM01P4R1 to form a complete 80A-class solder-tab lithium battery interconnection solution.

SYC (Sinyinda) launched SYCBCHM01P4R1, a 4-Pin high-current plug male connector (current-sharing version) specifically designed for 80A-class pure power lithium battery transmission scenarios. This product uses 4 identical 20A power terminals with no mixed signal pins, supporting 4 parallel current-sharing paths for 80A continuous current carrying. If a single pin fails, it can still operate at reduced rating to ensure system redundancy safety. It adopts copper-nickel plating (50-80μ") high-wear-resistant contact technology, with a plug/unplug lifespan of ≥1000 cycles and stable contact resistance ≤3mΩ; PA66 insulating substrate balances mechanical strength and temperature resistance, rated voltage DC 250V, operating temperature -40℃~+105℃. The integrated snap-lock mechanism provides ≥40N holding force (30% higher than 2-Pin/3-Pin versions), and the asymmetric housing design physically prevents reverse connection, with a recommended plug/unplug lifespan of 1000 cycles. It is particularly suited for high-power lithium battery application scenarios with rigid requirements for "high current density + dynamic current sharing + redundancy safety," such as 48V/60V lithium battery PACK parallel ports, energy storage PCS DC-side interconnection, battery swap station battery rack interfaces, and AGV fast-charging bases, precisely pairing with the female socket SYCBCHM01P4R1F to form a complete 80A-class pure power lithium battery interconnection solution.

This SS-12D10 straight-handle miniature slide switch (Vertical Slide Switch SS-12D10 High Current 3A 1P2T 3 Pin Through-Hole) features a design of "thickened anti-corrosion metal housing + black anti-slip textured POM straight handle + single row 3-pin silver-plated straight terminal pins + high-temperature-resistant high-current contact system." The circuit configuration is single-pole double-throw (1P2T two-position ON-ON), specifically optimized for power lines or strong-signal switching carrying up to 3A current; the anti-slip textured handle provides crisp damping and a strong detent feel, and the embedded thickened alloy silver-plated contacts effectively reduce contact resistance and temperature rise, preventing contact erosion; the terminals offer fast solder wetting and secure soldering. Widely used in high-power lighting fixtures, power tools, portable energy storage devices, household small appliances, and various PCB mainboards requiring safe high-current switching. 2D/3D drawings and free sample service are available.

This SS-43D03 straight-handle slide switch (SS-43D03 Vertical Slide Switch) features a precision design of "4P3T position structure (dual row 16 pins + 4 mechanical positioning reinforcement pins) + extended straight black slide handle + high-strength metal-clad housing + DIP through-hole mounting." Specifically tailored for hardware terminals that require multi-channel three-position synchronous switching (such as 4-channel audio source selection, high/mid/low three-stage function settings, multi-mode switching) and demand specific panel penetration depth and slide feel. The switch internally uses high-conductivity copper alloy silver-plated terminals and strong slider spring contacts, offering clear and distinct detent feel, precise switching without slipping, and extremely low contact resistance. The precision-stamped metal shield housing features thickened positioning pins on both sides, which firmly bond with the PCB after wave soldering, effectively resisting mechanical impact from the long handle's high leverage. Widely used in professional amplifiers/mixing consoles, high-end audio decoders, multifunctional electronic measuring instruments, industrial control panels, and intelligent power management systems. 2D/3D drawings and free sample service are available.

Sinyin Electronic original SK-22F03 is a DIP board-edge side-mount type 2P2T (2-pole 2-position 6-pin) dual-circuit slide switch. The product features side-downward recessed reinforced soldering tabs on both sides of the housing, which can effectively anchor into PCB board-edge through-holes and withstand lateral push-pull forces exceeding 40N, perfectly solving the engineering pain point of traditional side-toggle switches being prone to peeling and solder detachment. The 6-pin functional pins are equipped with thickened silver-plated contact strips, enabling 100% synchronous switching of two circuits (such as full disconnection of power positive and negative terminals, or power + signal). It fully meets the layout requirements of structural engineers, the low-impedance conduction needs of electronic engineers, quality control standards, and procurement's demand for fast delivery. Compliant with RoHS 2.0/REACH regulations, with free download of 2D/3D STEP models.

This DC power jack adopts a horizontal PCB through-hole design with a 3-pin structure, perfectly matching 5.5x2.1/2.5mm standard DC male plugs. Featuring high-elasticity copper alloy contacts and flame-retardant engineering plastic, it offers stable conductivity, durability against repeated insertion, and easy soldering, with specification drawings and free samples available.

DC-007B is a 10A high-current industrial-grade DC power jack, compatible with 5.5x2.1 and 5.5x2.5mm male plugs. Featuring a fully enclosed metal shielding shell structure, it provides high-power conduction, extremely low contact resistance, and electromagnetic interference resistance, with 2D/3D drawings and free samples available.

DC-025BM is an 8.5mm extended-thread DC power jack, compatible with 5.5x2.1 and 5.5x2.5mm power male plugs. The extended metal thread specifically solves the challenge of locking onto thick panels, secured with a hex nut, and the perforated solder tabs at the tail facilitate easy wire leads, with drawings and free samples available.