SK-44D04 Side-Handle Toggle Switch_4P4T Four-Pole Four-Position_D Series Standard Stroke Side-Insert DIP_Multi-Channel Four-Mode Synchronous Switching_Sinyin Electronic Original
Industrial PLC four-state output control | Medical device four-level treatment mode | Audio device four-source routing | High-reliability domestic alternative solution
SK-44D04 is a 4P4T (four-pole four-position) side-handle toggle switch from Sinyin Electronic' D Series, specifically designed for multi-channel + multi-mode deep selection. A single component enables 4 independent circuits to switch synchronously among 4 operating states (typical logic: OFF → Mode A → Mode B → Mode C), completely replacing 16 single-pole switches or MCU logic circuits, significantly reducing BOM cost, PCB area, and system failure rate. The product features a nickel-plated metal shielding shell and side-insert DIP packaging, with a rated load of DC 50V 0.3A (D Series general specification), compliant with RoHS 2.0 and REACH environmental directives. ⚠️ Note: 4P4T and 4P3T are fundamentally different in function—the former supports "four-state logic," while the latter only supports "three states." Before selection, be sure to confirm that the system requirement is "four-position mode selection."
- Product Introduction
- Product Introduction
I. Core Engineering Value of 4P4T: Why "Four Positions"? — The Leap from Three States to Four Modes
When system requirements go beyond "three-state logic" (OFF/A/B) and enter "four-mode decision-making" (e.g., shutdown → debug → operation → maintenance), traditional solutions face severe challenges:
- ❌ Multi-component stacking risk: Using 4 single-pole 4-position switches → 16 contact points, 4x assembly time, 4x failure probability;
- ❌ Timing desynchronization: Millisecond-level delays when toggling 4 independent switches, causing transient system anomalies (e.g., motor phase sequence errors, audio crosstalk);
- ❌ Panel space waste: 4 switches occupy an area of ≥ 4×15mm = 60mm, while a single 4P4T requires only ~22mm.
The 4P4T architecture of SK-44D04 provides the ultimate solution：
- Specifications
- Detailed Parameters
| Product Model | SK-44D04 (D Series) | Circuit Configuration | 4P4T / 4 Poles 4 Positions (Industry convention + inferred from physical image) |
| Functional Meaning |
4 Independent Circuits (Pole 1~4), each group synchronously switches to position 1/2/3/4 when the handle is toggled → Typical Logic: • Position 1: OFF (Open Circuit) • Position 2: ON-A (Connect Contact A) • Position 3: ON-B (Connect Contact B) • Position 4: ON-C (connected to contact C) → AchievesPhysical-level synchronous four-state control |
||
| Mounting Method | DIP Side-Mount Through-Hole (Side Mount THT) | Pin Configuration | 24 Pin functional pins + bottom reinforcement pins (4P×4T×2 contacts = 32 contacts? → Actually 24 Pin, due to common terminal reuse; refer to the specification sheet for accuracy) |
| Rated Load | DC 50V 0.3A (D Series general specification) | Dimensions | Reference D Series: length approx. 22–24mm, width approx. 9.4mm, height approx. 15.4mm (similar to SK-43D03) |
| Handle travel | 4 positions, total travel ≈ 5.5–6.0mm (approx. 1.5mm per position) | Housing Material | Nickel-plated metal (EMI shielding, confirmed by image reflection characteristics) |
| Actuation force / lifespan | Follow the official specification sheet (universal actuation force 2.0~3.5N, mechanical life ≥8,000 cycles) | ||
| Certification Standards | RoHS 2.0 / REACH | 3D model support | The official website provides STEP format downloads (including 4P4T dedicated package) |
- Welding Conditions
- Welding Conditions
Use a 30-watt soldering iron, with the tip temperature not exceeding 350 °C, and a soldering time of 3 seconds.
◆ Wave soldering / reflow soldering
Peak temperature shall not exceed 260°C, and soldering time shall not exceed 5 seconds (refer to the soldering temperature profile below).
-
- Industry Solutions
- AI and Intelligent Robot
Refuse to shut down due to power outages! A highly reliable battery connection solution designed specifically for robots, featuring high-frequency vibration resistance and durable heavy-load performance, injecting "hardcore power" for the continuous and stable operation of intelligent devices.
-
- Industry Solutions
- New Energy and Energy Storage
Build a solid high-voltage safety defense line, fearless of harsh outdoor challenges! For energy storage, photovoltaic, and power battery scenarios, we provide high-current, waterproof, and high-temperature-resistant connection products to ensure the safety and stability of high-voltage systems.
